VentSaver Vent Guards: Prevent Crushed Vent Pipes.
VentSaver products will help prevent crushed vent pipes by splitting and diverting the snow. This ingenious vent guard product also adds support and strength to your vent pipes, chimneys or masts. The innovative fin design cuts through packed ice and snow, causing the snow slide to divert around the pipe, and to assist in shedding the snow and ice from your roof. Installation is quick and easy. VentSaver is made from high quality, non-corrosive, aircraft grade aluminum, stainless steel cable and comes with stainless hardware.
VentSaver vent pipe guards prevent crushed vent pipes by adding support to the stack pipe or chimney while splitting ice and snow around vent pipes.
Use with Snow Guards
If damaging snow slides are a problem, we recommend installing snow guards as well as VentSavers. Snow guards help prevent snow slides by allowing snow and ice to melt completely or drop off in small amounts. We also recommend installing snow guards on upper roof areas to prevent the impact of snow and ice dropping from unprotected upper roof areas onto roof areas with VentSavers installed. Review the full product line for vent savers, snow guards, roof clamps and gutter leaf guards.
The Cricket Eliminator Vent Protection That Works!
The VentSaver FB151 Series is made from non-corrosive, powder-coated aluminum with a pre-punched stainless steel strap to fit smaller sizes of pipe from 1.5" - 4". Also provided are stainless-steel nuts, bolts and heavy duty 1 1/2" lag screws. It protects a standing profile of 6". Installation is quick and easy.
The VentSaver P383 Series is made from non-corrosive, powder-coated aluminum, and stainless-steel aircraft cable. Also provided are stainless steel nuts, bolts and heavy duty 1 1/2" lag screws. The 383 Series will fit any roof pitch and an array of pipe sizes from 1" to 14" around. It's 9" standing profile is designed to protect taller stacks such as chimneys, gas vents and masts. The beauty of the 383 Series is the variety of applications it will fit as well as the ease of installation.
The "New "VentSaver EZ Series is made from non-corrosive, mill aluminum and stainless-steel aircraft cable. Also provided are stainless steel nuts, bolts and heavy duty 1 1/2" lag screws. The EZ Series will fit any roof pitch and an array of pipe sizes from 1" to 14" around. It has a standing profile of 9 to 12 inches and is designed to protect taller stacks with the optional Wing Kit and Height Extension Kit.
The largest model, recommend for extreme snow conditions. The VentSaver HD Series is made from non-corrosive, powder-coated aircraft grade aluminum, and stainless-steel aircraft cable. Also provided are stainless steel nuts, bolts and heavy duty 1 1/2" lag screws. The HD Series will fit any roof pitch and an array of sizes from 1" to 14" around. The fin has a 14" standing profile that is designed to protect taller roof stacks, chimneys, gas vents and masts. Check out the new optional HDC Height Extension Kit that provides a combined profile height of 25 to 27 inches.
You Can Stop
Vent Pipe Damage
Stop Roof Pipe Damage with VentSavers.
Your roof is heavy with snow on a thick layer of ice. Rain speeds the natural glacial action as the large sheets slide from the roof taking your chimney or vent pipe with it. Before you know it, gallons of water have run into the attic. The house is filled with gas fumes or wood smoke. The insulation becomes saturated with water and the damage is done. You wake up one cold winter morning with your ceiling collapsed into the middle of your living room or worse.....your house is filled with fumes or on fire!
SS VentSaver Plate Kit (Standing Seam Roofs)
The SS VentSaver Kit is an adjustable fit mounting plate that secures to the seams with (4) non-penetrating RCT seam clamps. It allows the use of the VentSaver 151, 383, EZ or HD to be used on Standing Seam panels without penetrating the metal. The SS VentSaver utilizes a custom fit Ice Ramp to protect the base of the pipe from sliding snow and ice damage. The fin of the VentSaver protects the upper portions of the pipe. The adjustable all-aluminum SS VentSaver kit is manufactured in the USA and uses stainless steel set screws and fasteners. The quarter inch thick SS VentSaver plates allow our Standing Seam customers to use any of the VentSaver models without having to penetrate the floating panels.
"NEW" SD VentSaver Plate Kit (Screw Down Roofs)
The SD (Screw Down) VentSaver Plate is an adjustable fit screw-down mounting plate that fastens through the high seams of the metal roof panel, into the substructure below. It allows the use of the VentSaver 151, 383, EZ or HD to be used on PBR or corrugated screw-down panels even if the pipe location is off center in the valley. The SD VentSaver Mounting Plate utilizes a custom fit Ice Ramp to protect the base of the pipe from sliding snow and ice damage. The fin of the VentSaver protects the upper portions of the pipe. The quarter-inch thick, all-aluminum SS VentSaver Mounting Plate kit allows the HD an EZ Wig Kit and Height Extender to be used without modifications.